This useful feature allows actions on the same internal point from multiple KNX group addresses. To allow read requests, to allow write requests, to automatically send a write request to the KNX bus when its value changes, and to send a read request to the KNX bus when IntesisBox starts-up or after a bus reset.įor each point, one main group address and different listening group addresses can be defined. Any point in IntesisBox can be configured individually for different functionality. The IntesisBox's KNX EIB interface connects directly to the EIB bus and is optoisolated from the rest of the internal electronics. On the KNX side, IntesisBox simulates a KNX device and acts as if it was one more device into the KNX system. IntesisBox LON interface is compatible with twisted pair free topology channel (TP/FT-10) media, nowadays the most widely used media due to its robustness and the different topologies that can be used and mixed together. Follow the picture below to properly fill the fields requested.IntesisBox is a LonWorks device allowing to read/write points of other LonWorks devices connected to a LonWorks network and offering these point's values through its KNX/EIB interface. IBOX-BAC-MBM - Modbus to BACnet Gateway Intesis Integrate any Modbus RTU or TCP Slave device, or both at the same time, with a BACnet BMS or any BACnet IP or BACnet MS/TP controller. To configure the virtual input inside the Configurator, add the Ethernet Gateway, access the virtual Inputs window, and add a new Virtual Input. “vol”: “90”, we need to read this one “mute”: “0”, Specially suited for integration of thermostats, electricity meters, chillers, heating floors, heat pumps, PLCs into KNX EIB. “Artist”: “47726f6f766520436f766572616765”, IBOX-KNX-MBTCP-A and IBOX-KNX-MBTCP-B have been designed to offer full monitoring/control of Modbus slave devices or systems from KNX EIB installations. The response received from the Airscope device comes in a JSON format, following the example below: Following the formula described before, the overlapping factor will be approximately around 5 minutes and thus the computed start time of each action will be a value between 0.75 and 18 minutes.Īccording to section 2.3.1 of the Airscope manual (link above), the device will send the player's full status, including the current volume level, when it receives a GetPlayerStatus HTTP request as follows: The maximum duration of the simulation has been set to 200 minutes and thus it will be a value between 160 and 200 minutes. If the random order property is enabled, the order of execution of the actions won't follow the order in which they have been defined but it will be determined randomly.įor example, 10 actions have been defined with a duration of 15 minutes that means each action will have a duration between 10.5 and 19.5 minutes. The start time represents the time the server must wait before launching the action after the previous action terminated. 9121 server - knx ibox-mbs-knx-100 500,00 gateway modbus 9116 server - knx ibox-mbs-knx-a 990,00 gateway modbus server - knx 9118 ibox-mbs-knx-b 2. simulation duration - sum of actions durations) / num of actions. The overlapping factor is calculated as (max. The start time of each action is determined by calculating a random value between 15% and 120% of an overlapping factor. After these values are defined, the server then defines the sequence of actions the simulation will perform. Also the maximum duration of the simulation is computed by choosing a random value between 80% and 100% of the value you specified in the Configurator. The server computes a random duration of each action by choosing a value between 70% and 130% of the value specified in the configurator. The duration fields in the presence simulator are just sample values used to schedule the actions in the simulation. Import/Export commands from/to another project.Virtual Output: Change Volume from Thinknx UI.Virtual Input: Get Volume from Airscope.Managing Z-Wave nodes: acquisition, exclusion, parameters and associations.Reading Hue Bridge configuration and creating Hue Lights Groups.
0 Comments
Leave a Reply. |